Wirebench
AWG, ft, °Fmm², m, °C

Wire and cable size calculator

Recommended copper and aluminum conductor sizes checked against NEC 310.16 ampacity, 110.14(C) terminals, 240.4(D) limits, and voltage drop.

Circuit parameters

A
V
ft
Phase
Duty cycle (NEC 210.19 / 215.2)
Insulation rating
Terminal rating (NEC 110.14(C))
°F
%
CCC
Recommended conductor sizes No result
Copper (Cu) —
—
Enter load and distance
Aluminum (Al) —
—
Enter load and distance

Enter load, voltage and distance to size copper and aluminum conductors.

Design ampacity req.
—
Copper drop
—
Aluminum drop
—
Next std breaker (240.6)
—
Cu EGC (250.122)
—
Al EGC (250.122)
—

Materials take-off

Line item Copper option Aluminum option Qty / Length

IEC mode uses conservative AWG equivalents from NEC Table 310.16 for ampacity and IEC 60228 resistance at 20 °C adjusted to 75 °C for voltage drop.

Advertisement

How NEC wire sizing balances ampacity and voltage drop

Selecting an electrical conductor requires satisfying two independent constraints simultaneously: thermal ampacity under NEC Article 310 and voltage drop performance under NEC 210.19(A) and 215.2(A). The larger wire gauge required by either criterion governs the final installation.

I_required = I_load × (1.25 if continuous else 1.00) Size_ampacity: smallest gauge where min(I_adjusted, I_terminal) ≥ I_required and I_required ≤ OCPD_240.4(D) Size_drop: smallest gauge where %VD = (K × I_load × R × L / 1000) / V_system × 100 ≤ Max_VD%

Ampacity and continuous loads: Under NEC 210.19(A)(1) for branch circuits and 215.2(A)(1) for feeders, conductors supplying continuous loads (running 3 hours or more) must have an allowable ampacity not less than 125% of the continuous load before applying terminal limits. Ambient temperatures above 30 °C (86 °F) or more than three current-carrying conductors in a raceway require derating from the insulation column using NEC 310.15(B) and (C).

Voltage drop and EGC upsizing (NEC 250.122(B)): Although NEC informational notes recommend keeping branch-circuit drop within 3% and combined feeder-plus-branch drop within 5%, voltage drop calculations use the actual load current (not the 125% continuous multiplier). Whenever you increase ungrounded conductors above the code-minimum ampacity size to meet voltage drop, NEC 250.122(B) requires increasing the equipment grounding conductor proportionally by circular mil area.

Three worked wire sizing examples

Example 1: 40 A continuous EV charger at 240 V, 75 ft (Ampacity governs)

A Level 2 EVSE draws 40 A continuous at 240 V single-phase over a 75 ft one-way run in 30 °C ambient with three conductors in EMT, 90 °C THHN on 75 °C breakers, and a 3% drop limit.

Design current = 40 A × 1.25 = 50 A Copper ampacity check: 8 AWG Cu = 50 A at 75 °C terminals (satisfies 50 A) Copper voltage drop: 2 × 40 × 0.778 × 0.075 / 240 = 1.95% (≤ 3%) Aluminum ampacity check: 6 AWG Al = 50 A at 75 °C terminals (2.02% drop)

Both copper (8 AWG) and aluminum (6 AWG) meet the 3% voltage drop budget with margin to spare, so thermal ampacity governs the conductor selection on this 50 A circuit.

Example 2: 40 A non-continuous shop circuit at 240 V, 250 ft (Voltage drop governs)

The same 40 A load is now non-continuous (100% duty) and located 250 ft away in an outbuilding, with a 3% maximum voltage drop.

Ampacity minimum: 8 AWG Cu (50 A at 75 °C) or 8 AWG Al (40 A at 75 °C) Voltage drop at 8 AWG Cu: 2 × 40 × 0.778 × 0.250 / 240 = 6.48% (exceeds 3%) 4 AWG Cu drop: 2 × 40 × 0.308 × 0.250 / 240 = 2.57% (≤ 3%) 2 AWG Al drop: 2 × 40 × 0.319 × 0.250 / 240 = 2.66% (≤ 3%)

Distance forces a jump of two trade sizes in copper (from 8 AWG to 4 AWG) and three sizes in aluminum (from 8 AWG to 2 AWG). Because the phase conductors were upsized for voltage drop, NEC 250.122(B) also scales the 10 AWG copper EGC up to 4 AWG copper (26,242 cmil required > 26,240 cmil of 6 AWG).

Example 3: 100 A continuous 480 V 3-phase feeder in 40 °C, 6 CCC, 300 ft

A 480 V 3-phase continuous feeder carries 100 A for 300 ft in a 40 °C factory truss with six current-carrying 90 °C conductors in raceway and 75 °C equipment lugs.

Design current = 100 A × 1.25 = 125 A Derating factors: 0.91 (40 °C) × 0.80 (6 CCC) = 0.728 1/0 Cu adjusted = 170 × 0.728 = 123.8 A (short of 125 A) 2/0 Cu adjusted = 195 × 0.728 = 142.0 A ≥ 125 A (75 °C terminal = 175 A) 2/0 Cu voltage drop = √3 × 100 × 0.0967 × 0.300 / 480 = 1.05%

Ambient derating and bundling govern at 2/0 AWG copper, whereas 480 V 3-phase keeps voltage drop to just 1.05% across 300 ft.

Frequently asked questions

When does voltage drop govern wire size instead of ampacity? Voltage drop governs on long runs or low-voltage systems (12 V, 24 V, 120 V) where cable resistance causes more than 3% or 5% drop even though a smaller gauge could safely carry the thermal current.
When should I enable the 125% continuous load toggle? Enable 125% for loads expected to operate at maximum current for three hours or longer (EV chargers, commercial lighting, electric space/water heating) per NEC 210.19(A)(1) and 215.2(A)(1).
Do I also need to upsize the equipment grounding conductor when I upsize for voltage drop? Yes. NEC 250.122(B) requires increasing the EGC circular mil area in the same proportion that the ungrounded circuit conductors were increased above the minimum ampacity size.

Related calculators and reference charts

Recommended Cu / Al —
No result View