Wirebench
AWG, ft, °Fmm², m, °C

Conduit fill calculator

Mixed-wire NEC Chapter 9 fill percentage, 53% / 31% / 40% compliance check, jam ratio warning, and scaled conduit cross-section.

Raceway and conductors

Conduit type (NEC Ch. 9 Table 4)
Run type
Normal raceway
Conductors (AWG, insulation, qty)
Include all phase, neutral, and equipment grounding conductors.
Conduit fill No result
— %

Add conductors to calculate conduit fill.

NEC fill limit
—
Wire area / total
—
Spare capacity
—
Total conductors
—
Min legal trade size
—
Jam ratio (D / d)
—

Cross-section packing and conductor breakdown

Wire Type Qty Each (in²) Total (in²) Share

IEC mode maps each mm² conductor to its conservative NEC AWG equivalent for Chapter 9 Table 5 outside dimensions and displays metric areas in mm².

Advertisement

NEC Chapter 9 conduit fill rules and jam ratio

Conduit fill is calculated by dividing the sum of the cross-sectional areas of all enclosed conductors (NEC Chapter 9 Table 5) by the total internal cross-sectional area of the raceway (NEC Chapter 9 Table 4).

% Fill = (Σ (N_i × A_wire,i) / A_conduit) × 100 NEC limits (Table 1): 1 wire ≤ 53%, 2 wires ≤ 31%, 3+ wires ≤ 40%, Nipple (≤ 24 in) ≤ 60% Jam ratio = D_conduit_ID / d_wire_OD (danger zone: 2.8 to 3.2 for 3 equal wires)

Why 2 wires have a lower fill limit (31%) than 3 wires (40%): Two conductors lying side-by-side inside a circular pipe leave awkward crescent voids and tend to pinch when pulled around elbows. Once a third conductor is present, conductors nest in a triangular bundle that fills circular geometry more predictably, allowing 40% fill.

Jam ratio warning (2.8 to 3.2): When three conductors of equal or nearly equal outside diameter are pulled into a conduit where the internal pipe diameter is 2.8 to 3.2 times the wire diameter, the three wires can align side-by-side across a bend and lock solidly in the raceway. If your fill % passes at 40% or less but the jam ratio lands between 2.8 and 3.2, stepping up one trade size eliminates pulling damage.

Three worked mixed-wire conduit fill examples

Example 1: 100 A feeder with 3 × 3 AWG THHN + 1 × 8 AWG THHN ground in EMT

Three 3 AWG THHN current-carrying conductors (0.0973 in² each) plus one 8 AWG THHN equipment ground (0.0366 in²) are pulled into EMT.

Total wire area = (3 × 0.0973) + 0.0366 = 0.3285 in² (4 wires → 40% limit) 1" EMT 40% limit = 0.864 × 0.40 = 0.3456 in² Actual fill = 0.3285 / 0.864 = 38.02% (≤ 40%, PASS) Jam ratio on 3 AWG = 1.049 / 0.352 = 2.98 (JAM WARNING: 2.8 to 3.2)

Even though 1" EMT passes the 40% fill limit at 38.0%, its jam ratio of 2.98 falls directly inside the 2.8–3.2 danger zone for three 3 AWG conductors. Stepping up to 1-1/4" EMT (22.0% fill, D/d = 3.92) avoids binding on long pulls with bends.

Example 2: Service feeder with 3 × 4/0 THHN + 1 × 6 AWG THHN in PVC Sch 40

Three 4/0 AWG THHN conductors (0.3237 in² each) and one 6 AWG THHN ground (0.0507 in²) run in Schedule 40 PVC conduit.

Total wire area = (3 × 0.3237) + 0.0507 = 1.0218 in² 1-1/2" PVC Sch 40 40% limit = 1.986 × 0.40 = 0.794 in² (FAIL, 51.5%) 2" PVC Sch 40 40% limit = 3.291 × 0.40 = 1.316 in² (PASS, 31.0%)

A 2" PVC Schedule 40 conduit is the minimum legal trade size at 31.05% fill, leaving 0.294 in² of spare area inside the 40% limit.

Example 3: Multi-circuit panel homerun in a 3/4" EMT nipple (≤ 24 in)

A short 18-inch EMT chase nipple between two panels holds eight 12 AWG THHN (0.0133 in²) and six 10 AWG THHN (0.0211 in²) conductors (14 conductors total).

Total wire area = (8 × 0.0133) + (6 × 0.0211) = 0.2330 in² 3/4" EMT total area = 0.533 in² → 43.7% fill Standard run (40% limit): FAIL (43.7% > 40%) Nipple ≤ 24 in (60% limit): PASS (43.7% ≤ 60%)

Under NEC Chapter 9 Table 1 Note 4, nipples 24 inches or shorter may fill up to 60% and do not require NEC 310.15(C)(1) bundling ampacity derating.

Frequently asked questions

What are the NEC Chapter 9 Table 1 conduit fill limits? Maximum fill is 53% for 1 conductor, 31% for 2 conductors, and 40% for 3 or more conductors. Nipples 24 inches (600 mm) or shorter may be filled up to 60%.
What is conduit jam ratio and why does it matter? When 3 wires of the same outside diameter have a conduit ID to wire OD ratio (D/d) between 2.8 and 3.2, they can align side-by-side and jam in bends. Upsizing the conduit by one trade size eliminates the jam risk.
Do equipment grounding conductors count toward conduit fill? Yes. Every phase, neutral, traveler, and equipment grounding conductor inside the raceway counts toward both conductor count and total cross-sectional area.

Related calculators and reference charts

Conduit fill —
No result View