Wirebench
AWG, ft, °Fmm², m, °C

Hot tub, spa and pool pump wire calculator

NEC Article 680 copper-only branch circuit sizing, insulated green EGC, 5-ft/line-of-sight GFCI disconnect verification, and materials take-off.

Spa and pump parameters

240 V spa and pool pump presets
A
9.6 kW (50.0 A at 125%)
Duty factor
Circuit configuration (Copper only per Art. 680)
Self-contained hot tubs with 120 V controls require a neutral (4-wire).
Conduit with individual THWN-2 copper wires and insulated green EGC.
ft
%
ft
NEC 680.13: min 5 ft (1.5 m)
Disconnect visibility
°F
Copper branch conductors (NEC Art. 680) No result
— Copper only

Select a preset or enter spa load and distance.

Insulated green Cu EGC —
NEC 680.21(A)(1) / 680.42 requires an insulated copper green EGC (min 12 AWG).
5-ft & line-of-sight GFCI —
NEC 680.13 / 680.44 disconnect check.
GFCI breaker (240.6)
—
Insulated green EGC
—
Voltage drop
—
Voltage at spa
—
PVC Sch 40 conduit
—
Bonding wire (680.26)
8 AWG Cu solid

Materials take-off list

Line item Specification (NEC Art. 680) Qty / Length

IEC mode uses conservative AWG equivalents from NEC Table 310.16 for ampacity and IEC 60228 resistance adjusted to 75 °C for voltage drop.

Advertisement

NEC Article 680 wiring rules for hot tubs, spas, and pool pumps

Installations around pools, spas, and hot tubs carry elevated shock risk and chemical corrosion exposure, so NEC Article 680 imposes stricter conductor, grounding, and disconnect requirements than ordinary branch circuits.

Conductors: Copper ONLY (NEC 680.21(A)(1), 680.42) — aluminum prohibited Equipment Ground: Insulated green copper, min 12 AWG, Table 250.122 + 250.122(B) GFCI & Disconnect: Class A GFCI (680.44) + readily accessible within sight and ≥ 5 ft from water (680.13) Convenience Outlet: 125 V 15/20 A GFCI receptacle 6 ft to 20 ft from inside wall (680.22(A))

Copper-only and insulated green EGC: Individual THWN-2 or XHHW-2 copper conductors in PVC Schedule 40/80 or liquidtight nonmetallic conduit (LFNC-B) are the standard outdoor method from the GFCI spa panel to the hot tub or pool pump. The equipment grounding conductor must be insulated copper (green) and never smaller than 12 AWG for pool motors or the Table 250.122 value for the breaker (10 AWG Cu for 30–60 A breakers). If phase wires are upsized for voltage drop, NEC 250.122(B) requires upsizing the green EGC proportionally.

Interior NM-B vs. outdoor conduit: Inside a single-family dwelling, NEC 680.42(C) permits NM-B copper cable from the main panel to the exterior GFCI spa disconnect, but NEC 334.80 restricts NM-B to the 60 °C column (6 AWG NM-B = 55 A max, so a 60 A circuit requires 4 AWG NM-B). NM-B can never be used outdoors or underground.

240 V Hot tub and pool pump quick reference (Copper only)

GFCI breaker Max continuous (80%) Cu THWN-2 (75 °C) Cu NM-B interior (60 °C) Insulated green EGC Min PVC Sch 40 (4-wire)

Three worked Article 680 examples

Example 1: Standard 50 A 240 V 4-wire hot tub, 60 ft

A typical outdoor 4-wire hot tub draws 40 A continuous at 240 V (9.6 kW) 60 ft from the main panel, wired in PVC Schedule 40 conduit with THWN-2 copper conductors and a GFCI spa panel mounted 8 ft from the tub.

Design current = 40 A × 1.25 = 50.0 A → 50 A 2-pole GFCI breaker 75 °C Cu ampacity: 8 AWG Cu = 50 A (6 AWG Cu = 65 A commonly pulled for lower drop) 8 AWG Cu drop: 2 × 40 × 0.778 × 0.060 / 240 = 1.56% (≤ 3%) Insulated EGC (Table 250.122): 10 AWG insulated green Cu Conductors: Three 8 AWG Cu (2 Hots + Neutral) + One 10 AWG green Cu in 3/4" PVC Sch 40

Wait: many tub manufacturers specify 6 AWG copper even on a 50 A circuit for lower voltage drop or shared 50/60 A heater boards—always verify the spa nameplate manual before pulling 8 AWG.

Example 2: 60 A dual-pump spa with interior NM-B + outdoor whip, 75 ft

A large 60 A 4-wire spa (48 A nameplate load) runs 55 ft through finished interior joists to an outdoor GFCI spa panel 7 ft from the tub, plus a 20 ft outdoor PVC/LFNC run.

Design current = 48 A × 1.25 = 60.0 A → 60 A 2-pole GFCI breaker Interior NM-B (60 °C NEC 334.80): 6/3 NM-B is 55 A (TOO SMALL for 60 A load) → 4/3 NM-B (70 A) Outdoor conduit (75 °C): 6 AWG Cu THWN-2 = 65 A ≥ 60 A (passes!) Insulated EGC: 10 AWG insulated green Cu (Table 250.122 for 60 A) 6 AWG Cu drop at 75 ft: 2 × 48 × 0.491 × 0.075 / 240 = 1.47%

Running 4/3 NM-B indoors (or switching to 6 AWG SER / 6 AWG THWN-2 in conduit indoors) satisfies the 60 A load, while 6 AWG THWN-2 in 3/4" PVC/LFNC handles the wet outdoor leg to the spa.

Example 3: 30 A 240 V 3-wire pool pump 150 ft from panel

A 240 V pool pump circuit (24 A load, 30 A GFCI breaker, no neutral) runs 150 ft in PVC Schedule 40 conduit to a pool equipment pad.

Design current = 24 A × 1.25 = 30.0 A → 30 A 2-pole GFCI breaker Ampacity min: 10 AWG Cu (30 A per 240.4(D)), drop = 2 × 24 × 1.24 × 0.150 / 240 = 3.72% (> 3%) Upsize for ≤ 3% drop: 8 AWG Cu, drop = 2 × 24 × 0.778 × 0.150 / 240 = 2.33% (≤ 3%) EGC upsizing (NEC 250.122(B)): 10 AWG × (16,510 / 10,380) = 16,510 cmil → 8 AWG insulated green Cu

Because the phase conductors were upsized from 10 AWG to 8 AWG for voltage drop, NEC 250.122(B) requires upsizing the insulated green copper EGC to 8 AWG as well.

Frequently asked questions

Why does NEC Article 680 require copper conductors and an insulated green ground? Pool and spa chemicals and damp environments corrode aluminum splices and bare ground wires rapidly. NEC 680.21(A)(1) and 680.42 require copper conductors and an insulated green copper EGC (minimum 12 AWG for pool motors) in wet/outdoor runs.
Where must the GFCI spa disconnect be located under NEC 680.13? The maintenance disconnect must be readily accessible, within sight from the spa or pool equipment, and at least 5 ft (1.5 m) horizontally from the inside wall of the water vessel unless separated by a permanent barrier.
Can I run 6/3 NM-B Romex all the way to an outdoor hot tub? No. NM-B is prohibited outdoors and in wet/damp locations (NEC 334.12(B)(4)). You can only use NM-B inside dry dwelling walls up to the spa disconnect panel, and at 60 °C (where 6 AWG is capped at 55 A).

Related calculators and reference charts

Spa Cu / EGC / GFCI —
No result View