Residential electrical panel load calculator
Compute NEC Article 220 (Article 120 in 2026 NEC) dwelling unit demand VA and Amps, 100A/150A/200A/400A service sizing, and NEC 310.12 Cu/Al conductors.
Dwelling loads
Enter home square footage and fixed appliances to calculate service demand.
- Standard method (220 Part III)
- —
- Optional method (220.82)
- —
- Calculated current (240 V)
- —
- Service Cu wire (310.12)
- —
- Service Al wire (310.12)
- —
- Cu GEC (Table 250.66)
- —
NEC Article 220 / 2026 Article 120 demand breakdown
2026 NEC reorganization note: Load calculation rules formerly in Article 220 are renumbered to Article 120 in the 2026 NEC. Dwelling general lighting (3 VA/sq ft), small-appliance/laundry allowances (1,500 VA each), and Table 220.42/220.55 demand factors remain unchanged; EVSE (220.57) is included at the greater of 7,200 VA or nameplate rating at 100%.
| Load category | Connected VA | Demand factor | Calculated VA | NEC reference |
|---|
| Standard service | 83% min ampacity | Copper SE (310.12) | Aluminum SE (310.12) | Cu GEC (250.66) |
|---|
Dwelling load calculation methodology: NEC Article 220 and 2026 NEC Article 120
Performing an accurate residential service calculation prevents undersized main breakers, utility transformer overloads, and failed final inspections. The National Electrical Code provides two primary dwelling calculation paths—the Standard Method (NEC Article 220 Part III, renumbered Article 120 in the 2026 NEC) and the Optional Dwelling Unit Method (NEC 220.82)—both evaluated at a nominal 120/240 V single-phase service.
General Lighting & Receptacles (220.42): 3 VA × Area_sqft + 1,500 VA × SmallApp + 1,500 VA × Laundry
Demand: 100% of first 3,000 VA + 35% of (3,001 to 120,000 VA) + 25% over 120,000 VA
Fixed Appliances (220.53): Sum of fastened-in-place appliances (× 0.75 if 4 or more; excl. range/dryer/HVAC/EV)
Electric Dryer (220.54): max(5,000 VA, nameplate VA) at 100%
Electric Range (Table 220.55 Col C): 8,000 VA up to 12 kW (+5% per kW over 12 kW)
HVAC Noncoincident (220.60): max(Central AC VA, Electric Heat VA) at 100%
EVSE (220.57): max(7,200 VA, nameplate VA) at 100% | Spa/Hot Tub: 100% nameplate VA
Service Amps = Total_Calculated_VA / 240 V
Why is Article 220 moving to Article 120 in the 2026 NEC? Under the 2026 NEC reorganization, all branch-circuit, feeder, and service load calculation requirements leave Chapter 2 and relocate to Chapter 1 as Article 120. Engineers, contractors, and plan reviewers referencing 2020/2023 editions cite Article 220, while 2026 jurisdictions cite Article 120—the underlying 3 VA/sq ft general lighting allowance, 1,500 VA small-appliance and laundry circuits, and Table 220.42/220.55 demand scaling factors carry forward directly.
Standard vs. Optional Method: The Standard Method treats each appliance class with dedicated tables and typically produces a slightly more conservative amperage, making it universally accepted for new construction and service upgrades. The Optional Method (NEC 220.82) applies a single 100% tier for the first 10,000 VA of general loads plus 40% of the remainder, then adds the larger of 100% air conditioning or 65% central electric heat (100% if four or fewer heat zones are individually controlled vs. central unit). Notice that under NEC 220.82(B), EVSE and electric thermal storage loads often remain at 100% or within the 10 kVA + 40% tier depending on code edition—our calculator conservatively holds EVSE at 100% above 7,200 VA unless load management (EMS) limits total demand.
Choosing between 100 A, 150 A, 200 A, and 400 A panels: A calculated load at or below 100 A permits a 100 A service (common on small gas-heated cottages without EV chargers). Calculated loads between 101 A and 150 A require at least a 150 A service, though most contractors install a 200 A main panel because material cost differences are minor and future EV or heat-pump capacity is preserved. Any dwelling exceeding 200 A steps up to a 400 A (320 A continuous class) meter main—often split into dual 200 A panels—unless an NEC 750.30 energy management system (EMS) curtails EV charging during peak demand.
Three worked residential load calculation examples
Example 1: 1,200 sq ft gas-heated cottage (100 A service passes)
A 1,200 sq ft single-family home uses gas furnace heat and gas water heating, with two 20 A kitchen circuits, one laundry circuit, a 3 kVA central AC, dishwasher/disposal/microwave (3,200 VA across 3 appliances), and an electric clothes dryer (5,500 VA).
General lighting + 2 SA + 1 laundry = (1,200 × 3) + 3,000 + 1,500 = 8,100 VA
Table 220.42 demand = 3,000 + 0.35 × (8,100 - 3,000) = 4,785 VA
Fixed appliances (3 units, < 4 so 100%) = 3,200 VA
Dryer (220.54) = 5,500 VA | Central AC (220.60) = 3,000 VA
Total Standard VA = 4,785 + 3,200 + 5,500 + 3,000 = 16,485 VA → 16,485 / 240 = 68.7 A
At 68.7 A, a 100 A service panel fed with 4 AWG copper or 2 AWG aluminum (NEC 310.12) and an 8 AWG copper GEC easily satisfies code with over 31 A of spare capacity.
Example 2: 2,400 sq ft home with range, dryer, AC, and 48 A EV charger (200 A service)
A 2,400 sq ft modern residence adds a 12 kW electric range, 5.5 kW dryer, 4.5 kW electric water heater plus 3 kitchen appliances (3,600 VA across 4 total fixed appliances), 6,000 VA central AC, and an 11,520 VA (48 A) Level 2 EV charger.
General + SA + Laundry = (2,400 × 3) + 3,000 + 1,500 = 11,700 VA → 3,000 + 0.35 × 8,700 = 6,045 VA
4 Fixed Appliances (WH 4,500 + 3,600 = 8,100 VA × 0.75 per 220.53) = 6,075 VA
Range (Table 220.55 Col C) = 8,000 VA | Dryer = 5,500 VA | AC = 6,000 VA | EVSE = 11,520 VA
Total Standard VA = 6,045 + 6,075 + 8,000 + 5,500 + 6,000 + 11,520 = 43,140 VA
Service Current = 43,140 / 240 = 179.8 A → 200 A Service Panel
Total demand lands at 179.8 A, fitting comfortably inside a 200 A panel using 2/0 AWG copper or 4/0 AWG aluminum service conductors (NEC 310.12) and a 4 AWG copper GEC.
Example 3: 4,800 sq ft all-electric estate with heat strips, spa, and dual EVs (400 A service)
A 4,800 sq ft all-electric home has 18,900 VA general lighting/SA/laundry, 10,000 VA fixed appliances (4+ units at 75% = 7,500 VA), 8,000 VA range, 5,500 VA dryer, 20,000 VA electric heat strips (larger than 10,000 VA AC), 12,000 VA hot tub, and 19,200 VA across two EV chargers.
General demand = 3,000 + 0.35 × (18,900 - 3,000) = 8,565 VA
Fixed (7,500) + Range (8,000) + Dryer (5,500) + Heat (20,000) + Spa (12,000) + EVSE (19,200)
Total Standard VA = 8,565 + 72,200 = 80,765 VA → 80,765 / 240 = 336.5 A → 400 A Service
Because calculated load reaches 336.5 A, a 200 A service is insufficient. Upgrading to a 400 A (320 A meter-main) service with 400 kcmil copper (or parallel 2 × 3/0 Cu / 2 × 250 kcmil Al) feeds dual 200 A distribution panels cleanly.