Electric range, oven, and clothes dryer circuit calculator
Compare 10/3, 8/3, and 6/3 NM-B Romex against THHN conductors in conduit for 30A NEMA 14-30 dryers and 40A–60A NEMA 14-50 ranges and wall ovens.
Appliance & circuit parameters
Select an appliance preset or enter circuit breaker rating, load, and distance.
- Receptacle / Termination
- —
- Copper EGC (250.122)
- —
- Min conduit (4 THHN)
- —
- 240V Load / Demand
- —
10/3, 8/3, and 6/3 NM-B vs. THHN comparison
| Gauge / Cable | NM-B (60 °C, NEC 334.80) | THHN conduit (75 °C, 110.14(C)) | Typical appliance / NEMA | Drop at run |
|---|
Materials take-off & NEC 250.140 checklist
| Item | NM-B Romex option | THHN in conduit option | Spec / Quantity |
|---|
Range and dryer circuit sizing: NM-B vs. THHN and NEC 250.140
Sizing an electric clothes dryer, freestanding range, slide-in induction stove, or double wall oven circuit hinges on two Code interactions that frequently trip up installers: the 60 °C vs. 75 °C temperature-rating gap between NM-B cable and THHN conduit conductors, and the strict four-wire neutral/ground separation mandated by NEC 250.140.
NM-B ampacity (NEC 334.80): 10/3 NM-B = 30 A | 8/3 NM-B = 40 A | 6/3 NM-B = 55 A | 4/3 NM-B = 70 A
THHN in conduit (NEC 110.14(C) 75 °C): 10 AWG = 30 A (240.4(D) cap) | 8 AWG = 50 A | 6 AWG = 65 A
Nameplate to Amps (240 V): I = (kW × 1,000) / 240 V
NEC Table 220.55 range demand: 8 kW (33.3 A) for a single household range up to 12 kW
Why 8/3 NM-B stops at 40 A while 8 AWG THHN carries 50 A: Even though the copper inside NM-B cable carries 90 °C insulation, NEC 334.80 restricts Type NM-B ampacity to the 60 °C column of Table 310.16. Under the 60 °C column, 8 AWG copper is rated for exactly 40 A, and 6 AWG copper is rated for 55 A. That means a true 50 A circuit wired with Romex requires 6/3 NM-B cable, whereas pulling individual 8 AWG THHN copper conductors inside EMT or PVC conduit on 75 °C panel/receptacle lugs provides a full 50 A rating. Note that NEMA 14-50R receptacles are rated 50 A, and NEC Table 210.21(B)(3) permits installing a 50 A NEMA 14-50R receptacle on a 40 A circuit (since no 40 A NEMA configuration exists) as well as on a 50 A circuit.
10/3, 8/3, and 6/3 cable notation explained: Residential "/3" NM-B cable contains three insulated conductors (black hot, red hot, white neutral) plus one bare copper ground—making four total wires inside the jacket. Standard 240 V dryers (30 A) require 10/3 with ground and a NEMA 14-30R receptacle; 40 A ranges or cooktops allow 8/3 with ground; and 50 A ranges or heavy induction cooktops require 6/3 with ground. Two-wire "/2" cable (such as 10/2 or 6/2) lacks an insulated neutral and is legal only for pure 240 V appliances with zero 120 V loads (such as electric water heaters, welders, or some hardwired European induction cooktops whose spec sheet explicitly omits neutral).
Four-wire grounding rules under NEC 250.140: Since the 1996 NEC, every new dryer and electric range branch circuit must carry separate grounded (neutral) and equipment grounding conductors. Why? Heating elements operate at 240 V line-to-line, but the appliance's drum motor, electronic touchpad, clock, timer, and oven light run at 120 V line-to-neutral, placing continuous unbalanced current on the white neutral wire. On older three-wire NEMA 10-30 or 10-50 setups, the appliance frame was intentionally bonded to that live neutral—meaning an open or loose neutral energized the entire metal stove or dryer cabinet at 120 V. On a modern 4-wire NEMA 14-30 or 14-50 installation, always verify the brass or copper bonding strap between the neutral terminal and green ground screw on the appliance terminal block is disconnected before installing the 4-prong cord.
GFCI protection note (NEC 210.8): Under recent NEC editions (2020 and 2023 NEC 210.8(A)), 240 V laundry receptacles (NEMA 14-30R) and kitchen range receptacles (NEMA 14-50R) in many jurisdictions require 2-pole GFCI protection at the breaker. Using a 4-wire feeder with strict neutral-to-ground isolation prevents nuisance tripping on a 2-pole GFCI breaker.
Three worked range and dryer circuit examples
Example 1: 30 A residential clothes dryer, 5.5 kW at 45 ft (NEMA 14-30)
A new laundry room receptacle sits 45 ft from the main panel, serving a 5.5 kW (22.9 A at 240 V) electric clothes dryer.
Load current: 5,500 W / 240 V = 22.9 A (NEC 220.54 uses 5,000 W min for feeder load)
Breaker size: 30 A 2-pole (GFCI per 210.8(A) where adopted)
Conductors: 10/3 NM-B (30 A @ 60 °C) or 3 × 10 AWG THHN + 1 × 10 AWG EGC in 1/2" EMT
Voltage drop at 22.9 A, 45 ft: 2 × 22.9 × 1.24 × 0.045 / 240 = 1.07% (≤ 3%, pass)
Install 10/3 NM-B cable (or 10 AWG THHN in 1/2" EMT) to a NEMA 14-30R receptacle and install a 4-wire cord with the appliance neutral-to-chassis bonding strap removed.
Example 2: 50 A kitchen electric range, 12.0 kW at 75 ft (6/3 NM-B vs. 8 AWG THHN)
A 12.0 kW freestanding range with self-clean oven connects 75 ft from the breaker box. Under NEC Table 220.55 Note 4 / Column C, a single 12 kW range has an 8 kW (33.3 A) demand, though installers frequently specify a full 50 A circuit for modern high-draw induction ranges.
Demand / Nameplate: 8 kW demand = 33.3 A (50 A nameplate equivalent: 50 A max)
NM-B choice (60 °C, 334.80): 8/3 NM-B is 40 A (too small for 50 A breaker) → 6/3 NM-B (55 A)
THHN choice (75 °C in conduit): 8 AWG Cu THHN = 50 A → fits 50 A breaker in 3/4" EMT
Voltage drop at 33.3 A (8 kW demand), 75 ft:
6/3 NM-B (0.491 Ω/kft): 2 × 33.3 × 0.491 × 0.075 / 240 = 1.02%
8 AWG THHN (0.778 Ω/kft): 2 × 33.3 × 0.778 × 0.075 / 240 = 1.62%
If wiring in Romex for a 50 A breaker, use 6/3 NM-B with a NEMA 14-50R. If running conduit (EMT or PVC), 8 AWG THHN (three #8 current-carrying + one #10 green EGC in 3/4" EMT) legally carries 50 A at 75 °C.
Example 3: 40 A wall oven / cooktop vs. 60 A double oven (8/3 NM-B vs. 4/3 NM-B)
A kitchen remodel compares wiring a 9.6 kW single wall oven on a 40 A breaker versus a 14.4 kW double wall oven requiring a 60 A breaker at 55 ft.
40 A single wall oven (9.6 kW = 40.0 A):
8/3 NM-B = 40 A @ 60 °C (PASS, exact match) | 8 AWG THHN = 50 A @ 75 °C
EGC: 10 AWG Cu (NEC Table 250.122 for 40 A)
60 A double wall oven (14.4 kW = 60.0 A):
6/3 NM-B = 55 A @ 60 °C (undersized for continuous 60 A load) → 4/3 NM-B (70 A)
Conduit THHN: 6 AWG THHN = 65 A @ 75 °C in 3/4" EMT + 10 AWG Cu EGC
A 40 A circuit works cleanly with 8/3 NM-B (with NEMA 14-50R or hardwired whip), whereas a true 60 A double oven requires 6 AWG THHN in conduit or 4/3 NM-B / 4 AWG SER cable.